Senzor svjetla GTV luxomat (4800W, podesiv)

Senzor svjetla GTV luxomat (4800W, podesiv)

18,40
Izračun rata
Izračunaj ratu

Kalkulator je informativnog karaktera. Broj rata ovisi o vrsti kreditne kartice i o tome plaća li se online ili u trgovini. Za više informacija posjeti Načini plaćanja gdje su opisani svi načini plaćanja.

Broj rata Mjesečni iznos
2
9,20
3
6,13
4 -
6 -
12 -
-3% dodatnog popusta

= 17,85€ uz plaćanje odjednom (osim Diners i PayPal)

= 17,85€ uz plaćanje odjednom (osim Diners i PayPal)

dostupno Dobavljivo
nije dostupno Ronis Čakovec - Galerija sjever
nije dostupno Ronis Zagreb - Velesajam
nije dostupno Ronis Varaždin - skladište
Očekivana isporuka do 16.06.2026.
Točniju potvrdu roka i dostupnost javit ćemo ubrzo po narudžbi.

Informacije o raspoloživosti i vremenu isporuke su indikativne, ažuriraju se u intervalima i podložne su promjenama, te ne čine obvezujuću ponudu. Potvrdu dostupnosti i cijene ćemo vam dostaviti nakon što primimo i obradimo vašu narudžbu. Ugovor o kupnji je sklopljen tek po izdavanju računa.

18,40
Jamstvo 24 mjeseci
Plaćanje pouzećem, karticama, uplatom i PayPal-om
Povrat unutar 14 dana
The light sensor is used to automatically turn on the lights at dusk and off at dawn. This saves electricity. It consists of a sensor, which is protected in a waterproof housing, and an adjustable switch which can be used to adjust the sensitivity from 5 - 50 LUX. The sensor and the switch connect a 90cm cable. The switch is suitable for mounting on a DIN rail in an electrical cabinet. Installation: first make sure that there is no voltage in the mains determine the correct position of the sensor: it must be placed above the lamp to avoid poor performance drill a 13m diameter hole in the surface for the sensor gently insert the sensor head into the mounting hole connect the lamp (consumer) and power supply (mains) to the switch - the wiring diagram is given in the enclosed instructions after the installation, lower the el. current and check the operation of the sensor Technical specifications: Voltage: 220-240V AC / 50-60Hz Maximum permissible load: 4800W / 20A Switch dimensions: 66 x 36 x 90mm Weight: 130г Sensor hole mounting diameter: 13mm Sensor protection standard: IP54 Switch protection standard: IP20 Cable length from sensor: 90cm
Prikaži više
Šifra: 103108RN
EAN: 5901867108920
Više o proizvodu
Jamstvo
24 mjeseci

The light sensor is used to automatically turn on the lights at dusk and off at dawn. This saves electricity.

It consists of a sensor, which is protected in a waterproof housing, and an adjustable switch which can be used to adjust the sensitivity from 5 - 50 LUX.

The sensor and the switch connect a 90cm cable.

The switch is suitable for mounting on a DIN rail in an electrical cabinet.

Installation:

  • first make sure that there is no voltage in the mains
  • determine the correct position of the sensor: it must be placed above the lamp to avoid poor performance
  • drill a 13m diameter hole in the surface for the sensor
  • gently insert the sensor head into the mounting hole
  • connect the lamp (consumer) and power supply (mains) to the switch - the wiring diagram is given in the enclosed instructions
  • after the installation, lower the el. current and check the operation of the sensor

Technical specifications:

Voltage: 220-240V AC / 50-60Hz

Maximum permissible load:

4800W / 20A
Switch dimensions: 66 x 36 x 90mm
Weight: 130г
Sensor hole mounting diameter: 13mm
Sensor protection standard: IP54
Switch protection standard: IP20
Cable length from sensor: 90cm